Benelli/Beretta Flat Circle-Dot Sight Post - Tritium Dot, Green Circle

6 Review(s) Write a Review

On sale: ~~$52.95~~ $45.95

Part Number: BNFCDGTD3

Availability: Out of Stock.

Description
Product Features
Customer Reviews

Benelli/Beretta Flat Circle-Dot Sight Post - Tritium Dot, Green Circle

The Blitzkrieg Components Tritium Flat-Tipped Circle-Dot Sight Post provides a bold, fast sight picture in any lighting environment. The large, bright Tritium Dot provides a very effective low-light capability with the large green polymer ring around the dot provides an eye-catching daylight sight picture. Sight Post is precision machined from one piece of billet 416 Stainless Steel for durability and precise fit on all Benelli and Beretta Tactical Shotguns. The included Blitzkrieg Components elevation spacers enable 3 height levels for the front sight post ensuring proper zero on any Benelli shotgun with aperture sights as well as the Beretta 1301 tactical shotguns.

Features:

Bold, Fast Sight Picture
Bright Tritium Dot with Bright Green Polymer Ring around Dot
Billet Machined 416 Stainless Steel Construction
Black oxide matte black finish
Flat-Tipped Sight Profile
Elevation Spacers to properly fit all Benelli Shotguns with this type of sight as well as Beretta 1301 shotguns

Fit: Blitzkrieg's New Elevation Spacer System allows one sight to fit all Benelli Ghost Ring Sighted Shotguns as well as Beretta 1301 tactical shotguns (Benelli M4, M1014, Beretta 1301 Tactical, Benelli M1, M2 Tactical, M3 Tactical, Nova Tactical, Super Nova Tactical)

Parts Included:

Sight Post
2 Elevation Spacers
Lock Nut

Drop-In Installation: To install, simply unscrew the nut holding your factory sight post in place and remove it. Place the new Sight Post into the Sight Wings or Hood and place onto the sight base on the shotgun barrel. Then using the lock nut supplied with the sight, secure the sight post and hood in its place. Tighten slightly with 5.5mm wrench to engage locking surface of the nut. 2 Stainless Steel Elevation Spacers are included to adjust sight height as needed by adding them to the bottom of the sight post. For the short sight height that is typical on Benelli M4 and Beretta 1301, no spacer is needed to match factory sight height. For other Benelli models that use a taller front sight, 2 spacers are used to match the factory sight height. If you desire to have your sight tip be at exact center of our front sight hood, use 1 spacer and adjust your rear sight accordingly. For super easy installation, get one of our 5.5mm wrenches (sold separately).

MADE IN THE USA

Rating Snapshot

Select a row below to filter reviews.

Average Customer Ratings

5.0

View All Reviews - Reset

Reviews Sorting

Improved Front sight

I came across this sight looking to upgrade my front sight on my 1301. I already have Night Fision sights on my handguns so seeing they made one for the 1301 I was excited. I’ll be honest I was hesitant to buy on this sight since I’ve never heard of it, but saw some reviews on Reddit and was confindent on making my purchase. HUGE upgrade from the OEM, night and day difference. Highly recommend. I will say u have to buy the wrench to be able to install the sight. It’s an uncommon size wrench. **Note from Blitzkrieg for clarification -- Blitzkrieg Components designs and manufactures the sights and our Tritium Vials are from Night Fision.**

Did you find this helpful? 1 of 1 Found Helpful

Reviewed by: Vic760 from San Diego on 6/11/2025

Simply the best!!

I’ve been using Blitzkrieg sights exclusively for many years and on many platforms. Loved every single one of them. This one for my MAC1014 was nothing but perfection.. Smooth and fast target acquisition. You can’t go wrong with Blitzkrieg!

Did you find this helpful? 1 of 1 Found Helpful

Reviewed by: Bryan Tinsley from Atlanta, Georgia on 7/16/2025

Essential for Beretta 1301 Mod 2 Tactical

THIS is the front sight the 1301 mod 2 should have come with from the factory. Installation was a pig until you get the included nut threaded on the sight base. tweezers and small fingers help immensely. Then use the 5.5mm wrench (purchased here) which is essential and tighten it and enjoy. The wrench makes the second part easy peasy, along with the OEM nut removal. Just buy the wrench with it and be done. SO MUCH BETTER THAN OEM!!

Did you find this helpful? 1 of 1 Found Helpful

Reviewed by: FoghornLeghorn from USA on 2/14/2025

Big Improvement

I really like the new front sight. It's a big improvement over the standard white one and much easier to pick up. Definitely a solid upgrade. It's on an Agency Arms MAC 1014 which is a Benelli M4 Clone. Thanks again for your help!

Did you find this helpful?

Reviewed by: Suarez from CA on 5/19/2025

Now this is more like it!

I have a Benelli M4 H20 and it came with a ghost ring sights and they are pretty good. But, there is no tritium dot ( night sight ) and no bright circle around the dot. I was looking on line for a better front sight and found Blitzkrieg Components. I ordered the triangle with the tritium dot and it is awesome. Then they come out with the green circle with the tritium dot ( similiar to what you'd see on a pistol ) and it too is awesome. The colors pop and the tritium is very bright. Couldn't be happier with the sights that they are selling and highly recommend Blitzkrieg Components. I've been swapping back and forth between the triangle front sight and the circle dot. I like them both a lot and it is nice to have these options.

Did you find this helpful?

Reviewed by: Jason Wales from Hartselle on 10/19/2025

5.5mm Wrench for Benelli/Beretta Shotgun Front Sight

~~$15.95~~ $14.45 Sale

In Stock.

(6)

Add To Cart

Benelli/Beretta Front Sight Hood

~~$23.95~~ $20.95 Sale

Out of Stock.

(2)

Add To Cart

5.5mm Wrench for Benelli/Beretta Shotgun Front Sight

~~$15.95~~ $14.45 Sale

In Stock.

(6)

Add To Cart

Benelli/Beretta Front Sight Hood

~~$23.95~~ $20.95 Sale

Out of Stock.

(2)

Add To Cart

Benelli/Beretta Flat Circle-Dot Sight Post - Tritium Dot, Green Circle

Average Customer Ratings

Related Items

Accessories